iNano User Manual
Notice for Use
Thank you for choosing Eleaf products! Please read this manual carefully before use so as to use correctly. If you require additional information or have questions about the product or its use, please consult your local agents, or visit our website at www.eleafworld.com.
Product Introduction
iNano, an extraordinarily tiny e-cigarette kit by Eleaf, has a battery capacity of 650mAh. The atomizer is smartly inserted and locked in the box by a magnetic connector, which is much more convenient to use and carry. With five colors to choose, the iNano is the best choice of on-the-go kit.
How to Use
Atomizer Assembling:
1. First screw off the top section, fill e-liquid into the tank slowly along the glass tube and then screw the top section on tightly. (Note: please don’t overfill; please take several puffs without activating the atomizer and leave the atomizer sit for several minutes before use.)
2. Then insert the atomizer with the connector into the battery body.
3. Finally the iNano is ready for use.
Power on/off: Press the button 3 times in quick succession within 1.5 seconds, the blue button light will flash 3 times to show the iNano is powered on and keep holding the button to take a puff. In the same way, the device can be turned off.
Charging: Charge the device by connecting it with wall adapter or computer via a USB cable. The button light will turn red when the device is charging and the light will go out when fully charged. It will take about 2 hours to get a full charge via wall adapter.
Properties
Atomizer Protection: Each time when vaping time exceeds 10 seconds, the device will shut off automatically with the blue button light flashing 8 times.
Short-circuit Protection: Short-circuit occurs with the blue button light flashing 3 times.
Resistance Detecting: When the resistance at the output end is lower than 1.2ohm, there will be no output if user presses the button.
Low-voltage Protection: When the voltage of the device drops below 3.3V, the blue button light will flash 10 times and the output will cut off automatically. Charge the device to reactivate it.
Precautions
1. Only have your iNano kit repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur.
2. Do not leave the iNano kit in high temperatures or damp conditions, otherwise it may be damaged. The appropriate operation temperature is within 0℃ to 45℃ while charging and -10℃ to 60℃ while using.
3. Do not attempt to combine the iNano kit with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void.
Warnings
1. Please keep out of reach of children.
2. It is not recommended for use by young people or non-smokers.
Warranty
We are not responsible for any damages caused by human error. Legal warranty is applied.
You can get it by clicking Eleaf® iStick.
Thank you for choosing Eleaf products! Please read this manual carefully before use so as to use correctly. If you require additional information or have questions about the product or its use, please consult your local agents, or visit our website at www.eleafworld.com.
Product Introduction
iNano, an extraordinarily tiny e-cigarette kit by Eleaf, has a battery capacity of 650mAh. The atomizer is smartly inserted and locked in the box by a magnetic connector, which is much more convenient to use and carry. With five colors to choose, the iNano is the best choice of on-the-go kit.
How to Use
Atomizer Assembling:
1. First screw off the top section, fill e-liquid into the tank slowly along the glass tube and then screw the top section on tightly. (Note: please don’t overfill; please take several puffs without activating the atomizer and leave the atomizer sit for several minutes before use.)
2. Then insert the atomizer with the connector into the battery body.
3. Finally the iNano is ready for use.
Power on/off: Press the button 3 times in quick succession within 1.5 seconds, the blue button light will flash 3 times to show the iNano is powered on and keep holding the button to take a puff. In the same way, the device can be turned off.
Charging: Charge the device by connecting it with wall adapter or computer via a USB cable. The button light will turn red when the device is charging and the light will go out when fully charged. It will take about 2 hours to get a full charge via wall adapter.
Properties
Atomizer Protection: Each time when vaping time exceeds 10 seconds, the device will shut off automatically with the blue button light flashing 8 times.
Short-circuit Protection: Short-circuit occurs with the blue button light flashing 3 times.
Resistance Detecting: When the resistance at the output end is lower than 1.2ohm, there will be no output if user presses the button.
Low-voltage Protection: When the voltage of the device drops below 3.3V, the blue button light will flash 10 times and the output will cut off automatically. Charge the device to reactivate it.
Precautions
1. Only have your iNano kit repaired by Eleaf. Do not attempt to repair the unit by yourself as damage or personal injury may occur.
2. Do not leave the iNano kit in high temperatures or damp conditions, otherwise it may be damaged. The appropriate operation temperature is within 0℃ to 45℃ while charging and -10℃ to 60℃ while using.
3. Do not attempt to combine the iNano kit with parts from other brands of e-cigarettes. If it is damaged in this way, our company will not take on responsibility and your warranty will be void.
Warnings
1. Please keep out of reach of children.
2. It is not recommended for use by young people or non-smokers.
Warranty
We are not responsible for any damages caused by human error. Legal warranty is applied.
You can get it by clicking Eleaf® iStick.
No comments